-
James Heal
-
Hardware
-
Software
-
Firmware
-
Instruments
- Wrinkle Recovery Tester
- Wascator
- ProMace
- Titan 4, 5 and 10
- GyroWash
- FlexiFrame
- DynaWash
- TruBurst
- Orbitor
- Spray Rating Tester
- CrockMaster
- FlexiBurn
- Apollo
- SnagPod
- ThermaPlate
- TruFade
- AccuDry
- Martindale
- ElmaTear
- ElastAbrasion
- ProView
- Sample Cutters
- Titan
- Colour Assessment Cabinets
- Perspirometer
- Impulse
- Titan 1 2 3
- Crease Recovery Angle Tester
- DynaWash & DynaWash Duo
-
Operator's Guides
- GyroWash
- ElastAbrasion
- ProView
- Martindale 1300 Series
- Martindale 900 Series
- TruBurst
- FlexiBurn
- Orbitor
- HydroView - Hydrostatic Pressure Tester
- CrockMaster
- Wascator
- DynaWash & DynaWash Duo
- AquAbrasion 1819
- ThermaPlate
- Impulse
- Sock Abrasion Kit
- AccuDry
- Memmert Incubator IN30
- Spray Rating Tester
- Martindale 1600 Series
- AirPro - Air Permeability Tester
- TruFade
- Sample Cutters
- Titan
- General
- Tautex
- Perspirometer
- ElmaTear
- Martindale model 103
- Crease Recovery Angle Tester
- FlexiFrame
- ProDry
- Yellowing Test Kit
- Incubator / Oven
- Wrinkle Recovery Tester
- TruRain
- ProMace
- WickView
- SnagPod
- INSTALLATION GUIDE
- Drape Tester
-
Test Materials
-
EU Declaration of Conformity
-
Material Safety Data Sheets
-
General
-
Uncategorized
-
Filters
Results for "elmatear"
-
ElmaTear model 1555 - Operators Guide - English
Operator's Guides ElmaTearOperator's Guide version E
-
Which standards can be performed on ElmaTear?
Instruments ElmaTearThe following standards can be performed on the ElmaTear elmendorf tester:
-
Why does ElmaTear2 detect the wrong pendulum during calibration?
Instruments ElmaTearThe ElmaTear2 detects which pendulum is fitted by measuring the time taken for the pendulum to drop after it is released. If there is any friction or delay in the release of the pendulum this will lead to the wrong pendulum being detected.
-
Checking for friction on ElmaTear
Instruments ElmaTearSince this standard was written technology has move on considerably. We believe the method shown in ISO 1974 is outdated and better methods are available. The Elmatear 1555 guards against bearing friction in 2 ways....If the swing angle is below 147 degrees the Elmatear 1555 will reject the verification to alert the operator of the problem.
-
Why is the touchscreen not responding correctly on the ElmaTear2 855?
Instruments ElmaTearInstructions for calibrating the touchscreen on the ElmaTear2 855, if it is not responding correctly or as expected.
-
ElmaTear 855 - Operator's Guide - English
Operator's Guides ElmaTearThe Operator's guide for the ElmaTear 855 in English. Guidance on how to use this instrument is included in this guide.
-
ElmaTear 855 - Quick Start Guide - English
Operator's Guides ElmaTearThe Qucik Start Guide for the ElmaTear 855 in English. Guidance on how to use this instrument is included in this guide.
-
Why is the pendulum is not releasing on ElmaTear 655?
Instruments ElmaTearThings to check if the pendulum does not release on the ElmaTear 655, including: - If there is any damage on the pendulum arm that the release pin is in the right position
-
EU Declaration of Conformity for ElmaTear 1555
EU Declaration of Conformity ElmaTearThe EU Declaration of Conformity for ElmaTear 1555 in accordance with EN ISO 17050-1:2010
-
How do I change the pendulum release switches on the ElmaTear 655?
Instruments ElmaTearThe full instructions with images and diagrams are included in the PDF document.